Note 8/32/2014 from George Lewter - added the words"Slips" and "Terra Sigilatta" to make this topic more inclusive of the non-melted materials applied over clay bodies.
Due to the nature of the glaze, this is obviously NOT to be used for functional pieces (for those that are new to ceramics), only sculptural pieces and is best when lots of heavy texture / sprigging is used to accentuate the different levels or layers and therefore colours. Hope that makes sense.
These recipes and techniques come from an Australian ceramic artist by the name of Simone Fraser. I obtained these recipes whilst studying ceramics at college many years ago. Her website is well worth avisit to see someexamples ofhow she still uses theseengobes,dry glaze techniques today. www.simonefraser.com.au
Step One - Apply Engobe to leatherhard clay over texture and bisque fire to Cone 06. You can cover the entire tile or sponge back in places to reveal the clay body underneath, which gives you another variation (nice).
Photo below is to give you an idea of the colour of the engobe after bisque firing. You can also add more oxide to each engobe than I have here. Up to you. Test, test, test. The engobes don't look like much when initially fired to Cone 06 but at Cone 6 with dry glazes etc over the top, they work their magic. Incidently, I have used these under glazes too.
Engobe Base Recipe
Eckalite 60
Silica 20
Potash Feldspar20
Bentonite 3
Varations I have used
1. Iron Oxide 8%
2. Chrome 4%
3. YellowIron Ox3% + Copper Carb 3%
4. Cobalt 1.5%
Step Two - After bisque firing the engobed tiles, I apply various oxides washes over engobes then sponge off/back in areas to ensure that the underlying engobe is also visible.
NOTE: In all of the tiles shown here I have used a 'Rutile' wash (resulting in red) and a 'Manganese'wash (resulting in metallic dark brown to black). You will notice that the wash is prominent in the deeper texture here but that is up to you. Also, other oxides work too. I also mix a small a small amount of frit or Gertsley Borate and a little EPK to my oxide washes.
Also, when I wastaught this techniqueat college, we were only taught to use the engobe and dry glazes in combinations. I have found that adding the oxides washes just adds another dimension. Up to you. TEST.
Step Three - I then sponge on the 'Dry Glazes' so that they appear on the very surface. This allows the underlying engobe and oxide washes to show through. You will also want to leave some of the very surface free from dry glaze to enable the engobe to show in areas. Wipe back with a damp sponge in areas if you overdo the sponging on. I tend to overdo it.
There are endless possibilities with this dry glazing technique. They can be sponged on, brushed on and wiped back. I have not covered all the variations as they are endless.I find that it works well to use contrasting engobes/oxides under the glaze to achievethe best results.
Here are the 3 tiles again and how I did each one.
Tile One
This tile has the following;
- Engobe with 4% Chrome added to the base. Paintedcovering thewhole tile.
- Rutile wash on the left and Manganese wash on the right and sponged back lightly in places to reveal some engobe.
- Cobalt Dry Glaze (Base with 2% Cobalt) sponged over the very surface, making sure not to sponge in todeeper textured areas and leaving some areas of engobe still visible on the surface too(I probably overdid it a little here with the dry glaze).
Tile Two
This tile has the following;
- Engobe with1.5% Cobalt Carb added to the base. Paintedcovering thewhole tile.
- Rutile wash on the left and Manganese wash on the right and sponged back lightly in places to reveal engobe.
- Moss Green/Brown Dry Glaze (Base with 3.5% Yellow Iron Ox plus 3% Copper Carb) sponged all over the very surface, making sure not to sponge in deeper textured areas and leaving some areas of engobe visible on the surface. Moss Green/Brown tends to be green whereheavier and moss brown were lighter application is achieved.
Tile Three
This tile has the following;
- Engobe with 8% Iron Ox added to the base. Paintedcovering thewhole tile.
- Rutile wash on the left and Manganese wash on the right and sponged back lightly in places to reveal some engobe.
- Cobalt Dry Glaze (Base with 2% Cobalt) spongedover the very surface, making sure not to sponge in deeper textured areas and leaving some areas of engobe visible.
Dry Glaze Base Recipe
Eckalite 2 23(I think EPK would be a sub, as Eckalite is a Kaolin)
Soda Feldspar 16
Whiting (calc carb) 28
Molochite #200 23
Frit 4193 8
Add; 2% Cobalt for Blue
3.5% Yellow Iron Ox plus 3% Copper Carb for Moss Green / Brown
6% Copper Carb for Apple Green (i did not have an example of that
variation above)
If you have any questions, please let me know and make sure to have a look at Simone Fraser's website.
